
MOTOROLA, INC.

VOICE SURFR 33600 INTERNAL

Card Type                    Modem (asynchronous)
Chip Set                     Unidentified
I/O Options                  Speaker out, microphone
Maximum Modem Rate           33.6Kbps
Maximum Fax Rate             14.4Kbps
Data Modulation Protocol     Bell 103/212A

                             V.34, V.32bis, V.32, V.22bis, V.21, Bell 212,
                             Bell 103
Fax Modulation Protocol      ITU-T V.17, V.29, V.27ter, V.21 CH 2
Error Correction/Compression V.42, V.42bis, MNP5
Fax Class                    Class I
Data Bus                     16-bit ISA
Card Size                    Half-length, full-height card

[Image]

                                CONNECTIONS

        Function           Label             Function              Label

  Line in (RJ-11)               CN1      Speaker out                CN3

  Line out (RJ-11)              CN2      Microphone                 CN4

                        USER CONFIGURABLE SETTINGS

                    Function                      Label      Position

  Factory configured - do not alter               JP1      Unidentified

  Factory configured - do not alter               JP2      Unidentified

  Factory configured - do not alter               JP3      Unidentified

  Factory configured - do not alter               JP4      Unidentified

  Factory configured - do not alter               JP5      Unidentified

  Factory configured - do not alter               JP6      Unidentified

  Factory configured - do not alter               JP7      Unidentified

  Factory configured - do not alter               JP18     Unidentified

  Factory configured - do not alter               JP19     Unidentified

  Factory configured - do not alter               JP20     Unidentified

  Factory configured - do not alter               JP21     Unidentified

  Factory configured - do not alter               JP22     Unidentified

  Factory configured - do not alter               JP23     Unidentified

  Factory configured - do not alter               JP24     Unidentified



            SERIAL PORT ADDRESS

    Setting         JP16          JP17

  COM1 (3F8h)       Open          Open

  COM2 (2F8h)       Open         Closed

  COM3 (3E8h)      Closed         Open

  COM4 (2E8h)      Closed        Closed

                                 INTERRUPT

  Setting   JP8   JP9    JP10    JP11     JP12    JP13     JP14     JP15

  IRQ 2     Open  Open   Open    Open     Open    Open     Open     Closed

  IRQ 3     Open  Open   Open    Open     Open    Open     Closed   Open

  IRQ 4     Open  Open   Open    Open     Open    Closed   Open     Open

  IRQ 5     Open  Open   Open    Open    Closed   Open     Open     Open

  IRQ 7     Open  Open   Open   Closed    Open    Open     Open     Open

                         SUPPORTED COMMAND SET

                           Basic AT Commands

  AT, +++, A/

  A, E, H, M, O, S, V, X, Z

  &F, &V, &W, &Y, &Z

                          Extended AT Commands

  \K, \Q

  %A

                              S Registers

  S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S25, S26, S38

  Note: See MHI Help File for full command documentation.

                         Proprietary AT Command Set

                         AUTO FALLFORWARD/FALLBACK

  Type:          Configuration

  Format:        AT [cmds] &An [cmds]

  Description:   Controls auto fallforward/fallback

    Command                              Function

      &A0        Auto fallforward/fallback disabled

      &A1        Auto fallforward/fallback enabled

                         DATA CARRIER DETECT (DCD)

  Type:          Configuration

  Format:        AT [cmds] &Cn [cmds]

  Description:   Selects whether the DCD option is enabled or disabled

    Command                              Function

      &C0        DCD enabled

      &C1        DCD enabled after carrier signal detected

      &C2        Force DCD on and toggle DCD on disconnect

                           DATA SET READY (DSR)

  Type:             Configuration

  Format:           AT [cmds] &Sn [cmds]

  Description:      Selects DSR options

     Command                              Function

       &S0          DSR forced high, off at disconnect

       &S1          DSR forced high in data or online mode, off in
                    command or idle mode

       &S2          DSR follows carrier detect

       &S3          DSR is forced high in all modes













                         DATA TERMINAL READY (DTR)

  Type:                  Configuration

  Format:                AT [cmds] &Dn [cmds]

  Description:           Selects modem response to DTR

        Command                              Function

          &D0            Modem does not respond to DTR

          &D1            Modem goes to command mode after DTR goes is off

          &D2            Modem goes to command mode and disconnects
                         (hangs up) after DTR goes off; Auto-Answer is
                         disabled.

          &D3            Modem is initialized after DTR goes off

                                   DIAL

  Type:                  Immediate

  Format:                AT [cmds] D<#> [cmds]

  Description:           Dials telephone number according to any
                         modifiers included in the string

  Note:                  Any combination of modifiers can be used to
                         produce the desired dial functions in sequence.

        Command                              Function

          DL             Re-dial last number

          DP             Pulse dialing enabled

         DS=n            Dial stored telephone number n

          DT             Tone dialing enabled/Pulse dialing disabled

          DW             Dialing resumed following dial tone detection

          D,             Dialing paused for amount of time specified in
                         S8 register

          D!             Flash function initiated. Modem commanded to go
                         off-hook for specified time before returning
                         on-hook.

          D@             Wait for Quite Answer function enabled. Modem
                         waits until a "quiet answer," a ring-back signal
                         followed by silence up to the time specified in
                         S7, is received prior to executing the rest of
                         the dial string.

          D;             Modem returned to idle state after dialing. The
                         semicolon can only be placed at the end of the
                         dial command.

































                                 JACK TYPE

  Type:          Configuration

  Format:        AT [cmds] &Hn [cmds]

  Description:   Selects maximum connect speed

    Command                             Jack Type

      &H0        Auto-detect

      &H1        V.34

      &H2        V.32bis automatic

      &H3        V.32bis only

      &H4        V.32 automatic

      &H5        V.32 only

      &H6        V.22 only (2400-1200bps)

      &H7        V.22 only (1200bps)

      &H8        Bell 212 only

      &H9        Bell 103 only

      &H10       V.21 only

                           MODEM TO MODEM SPEED

  Type:          Configuration

  Format:        AT [cmds] &Gn [cmds]

  Description:   Sets the modem to modem speed

    Command                              Function

      &G5        4.8Kbps

      &G6        7.2Kbps

      &G7        9.6Kbps

      &G8        12.0Kbps

      &G9        14.4Kbps

      &G10       16.8Kbps

      &G11       19.2Kbps

      &G12       21.6Kbps

      &G13       24.0Kbps

      &G14       26.4Kbps

      &G15       28.8Kbps

      &G16       31.2Kbps

      &G17       33.6Kbps

                            REPORT INFORMATION

  Type:          Immediate

  Format:        AT [cmds] In [cmds]

  Description:   Displays information requested

    Command                              Function

       I0        Reports product code

       I1        Reports 000

       I2        Returns OK or ERROR

       I3        Report firmware revision number

       I4        Report configuration settings



                               RESULT CODES

  Type:          Configuration

  Format:        AT [cmds] Qn [cmds]

  Description:   Enables modem to send result codes to the DTE

    Command                              Function

       Q0        Result code sending enabled

       Q1        Result code sending disabled

       Q2        Call progress messages on originate

                              SPEAKER VOLUME

  Type:          Configuration

  Format:        AT [cmds] Ln [cmds]

  Description:   Controls speaker volume

    Command                              Function

       L0        Low volume setting

       L1        Low volume setting

       L2        Medium volume setting

       L3        Highest volume setting

                              TRELLIS CODING

  Type:          Immediate

  Format:        AT [cmds] &Un

  Description:   Controls trellis coding

    Command                              Function

      &U0        Trellis coding enabled

      &U1        Trellis coding disabled

                            Extended AT Commands

                                ANSWER MODE

  Type:          Configuration

  Format:        AT [cmds] %On [cmds]

  Description:   Sets the answer mode

    Command                              Function

      %O0        Answer mode if ringing

      %O1        Force to answer mode

      %O2        Automatic answer in originate mode

                           CHARACTER ABORT DELAY

  Type:          Configuration

  Format:        AT [cmds] %Kn [cmds]

  Description:   Sets the delay before character abort

    Command                              Function

      %K0        Enable 2 second delay

      %K1        Disable delay



                             CHARACTER LENGTH

  Type:          Configuration

  Format:        AT [cmds] \Bn [cmds]

  Description:   Sets the character length

    Command                              Function

      \B0        6 data bits, no parity, 1 stop bit

      \B1        7N1

      \B2        7P1

      \B3        8N1

      \B4        7P2

      \B5        8P1

                                COMPRESSION

  Type:          Configuration

  Format:        AT [cmds] %Cn [cmds]

  Description:   Selects data compression

    Command                              Function

      %C0        Data compression disabled

      %C1        Data compression enabled

                           CONNECT AND PROTOCOL

  Type:             Configuration

  Format:           AT [cmds] \Vn [cmds]

  Description:      Sets the connect and protocol message functions

     Command                              Function

       \V0          Connect and protocol message reports modem to modem
                    speed

       \V1          Connect and protocol message reports computer to
                    modem speed

       \V2          Connect message reports computer to modem speed/V.42
                    error correction

       \V3          Connect message reports computer to modem speed

                               CONNECT MODE

  Type:          Configuration

  Format:        AT [cmds] \Nn [cmds]

  Description:   Controls the type of connection the modem will operate
                 in

    Command                              Function

      \N0        Normal operation

      \N1        Direct operation

      \N2        MNP connection only

      \N3        V.42 LAPM, MNP or normal mode

      \N4        V.42 LAPM connection only

      \N5        V.42 LAPM or MNP mode

      \N6        Simulated controlled carrier











                                    DTR

  Type:          Immediate

  Format:        AT [cmds] %Zn [cmds]

  Description:   Controls the DRT function

    Command                              Function

      %Z0        Ignore DTR signal toggle

      %Z1        Dial stored phone number (0-3) on DTR toggle

      %Z2        Attempt to connect on DTR toggle

                               FLOW CONTROL

  Type:          Configuration

  Format:        AT [cmds] \Gn [cmds]

  Description:   Selects modem port flow control

    Command                              Function

      \G0        Flow control disabled

      \G1        XON/XOFF flow control

      \G2        XON/XOFF flow control only for transmitting data

      \G3        XON/XOFF flow control with pass-through

                                  PARITY

  Type:          Configuration

  Format:        AT [cmds] \Pn [cmds]

  Description:   Sets parity

    Command                              Function

      \P0        Even

      \P1        Space

      \P2        Odd

      \P3        Mark

      \P4        Automatic

                                  RETRAIN

  Type:          Immediate

  Format:        AT [cmds] %Q [cmds]

  Description:   Controls the retrain

    Command                              Function

      %Q0        Disable retrain

      %Q1        Attempt up to 3 retrains and disconnect if unsuccessful

      %Q2        Retrain until signal quality is good



















                                   SPEED

  Type:          Configuration

  Format:        AT [cmds] \Tn [cmds]

  Description:   Sets the computer to modem speed

    Command                              Function

      \T0        Autobaud

      \T1        Set to last AT command entry

      \T2        300bps

      \T3        1200bps

      \T4        2400bps

      \T5        4800bps

      \T6        7200bps

      \T7        9600bps

      \T8        12.0Kbps

      \T9        14.4Kbps

      \T10       16.8Kbps

      \T11       19.2Kbps

      \T12       21.6Kbps

      \T13       24.0Kbps

      \T14       26.4Kbps

      \T15       28.8Kbps

      \T16       31.2Kbps

      \T17       33.6Kbps

      \T18       38.4Kbps

      \T19       57.6Kbps

      \T20       76.8Kbps

      \T21       115.2Kbps

                                  TIMEOUT

  Type:                 Configuration

  Format:               AT [cmds] \Cn [cmds]

  Description:          Sets timeout, fallback, data buffer

       Command                              Function

         \C0            Timeout and fallback, speed buffer, no data
                        buffer

         \C1            Timeout and fallback, speed buffer, buffer
                        receive data

         \C2            Auto reliable, fallback with fallback character,
                        speed buffer, no receive data buffer

         \C3            Timeout and fallback, ITU-T V.14, buffer receive
                        data

         \C4            Timeout and fallback with fallback character,
                        ITU-T V.14, no data buffer

                            S(status) -REGISTERS

                          RETRANSMISSION COUNTER

  Type:          Register

  Format         AT [cmds] S70=n [cmds]

  Default:       100

  Range:         0-255

  Description:   Sets the number of retransmission tries

