
ARCHTEK CORPORATION

5634PEW

Card Type                    Modem/Fax card
Chip Set                     ESS
Maximum Modem Rate           56Kbps
Maximum Fax Rate             14.4Kbps
Data Modulation Protocol     Bell 103A/212A

                             ITU-T V.21, V.22, V.22bis, V.32, V.32bis,
                             V.34, V.90
Fax Modulation Protocol      ITU-T V.17, V.27ter, V.29, V.21CH2
Error Correction/Compression MNP5, V.42, V.42bis
Fax Class                    Class I
Data Bus                     PCI

[Image]

                                CONNECTIONS

         Function           Label             Function             Label

  Line in (RJ-11)                CN1      Line out (RJ-11)          CN2

                           SUPPORTED COMMAND SET

                             Basic AT Commands

  AT, +++, comma, A/

  A, B, E, H, P, Q, T, V, W, X, Y, Z

  &C, &P, &V, &W, &Y, &Z

                           Extended AT Commands

  \A, \G, \L

  %C

                                S Registers

  S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S21,
  S22, S29, S32, S33



  Note: See MHI Help File for full command documentation.

                         PROPRIETARY AT COMMAND SET

                            AUTO-MODE DETECTION

  Type:                  Configuration

  Format:                AT [cmds] Nn [cmds]

  Description:           Selects various options for the automatic
                         detection and negotiation of protocols during
                         the handshake process if the modem is
                         communicating with a remote modem of dissimilar
                         speed.

        Command                              Function

          N0             Auto-mode detection disabled

          N1             Auto-mode detection enabled

                          AUXILIARY RELAY CONTROL

  Type:             Configuration

  Format:           AT [cmds] &Jn [cmds]

  Description:      Enables/disables A/A1 relay driver. Not for use with
                    RJ-11 phone lines

      Command                             Jack Type

        &J0         Auxiliary relay is disabled

                            COMMUNICATIONS MODE

  Type:          Configuration

  Format:        AT [cmds] &Mn [cmds]

  Description:   Selects communications mode

    Command                                Mode

      &M0        Asynchronous mode

                            COMMUNICATIONS MODE

  Type:           Configuration

  Format:         AT [cmds] &Qn [cmds]

  Description:    Selects communications mode options

    Command                                Mode

      &Q0         Asynchronous mode, serial port speed follows connect
                  speed.

                           DATA SET READY (DSR)

  Type:          Configuration

  Format:        AT [cmds] &Sn [cmds]

  Description:   Selects DSR options

    Command                              Function

      &S0        DSR forced high

                         DATA TERMINAL READY (DTR)

  Type:          Configuration

  Format:        AT [cmds] &Dn [cmds]

  Description:   Selects modem response to DTR

    Command                              Function

      &D0        DTR override

      &D1        DTR toggle causes online command mode

      &D2        DTR toggle causes modem to go on-hook

                                   DIAL

  Type:                  Immediate

  Format:                AT [cmds] D<#> [cmds]

  Description:           Dials telephone number according to any
                         modifiers included in the string

  Note:                  Any combination of modifiers can be used to
                         produce the desired dial functions in sequence.

        Command                              Function

          DL             Re-dial last number

          DP             Pulse dialing enabled

          DT             Tone dialing enabled/Pulse dialing disabled

          DW             Dialing resumed following dial tone detection

          D,             Dialing paused for amount of time specified in
                         S8 register

          D!             Flash function initiated. Modem commanded to go
                         off-hook for specified time before returning
                         on-hook.

          D;             Modem returned to idle state after dialing. The
                         semicolon can only be placed at the end of the
                         dial command.

                          FACTORY DEFAULT PROFILE

  Type:             Configuration

  Format:           AT [cmds] &Fn [cmds]

  Description:      Sets values in active profile to values found in the
                    default profile

     Command                              Function

       &F0          Restore stored profile 0 after warm reset

       &F1          Restore stored profile 1 after warm reset

                               FLOW CONTROL

  Type:          Configuration

  Format:        AT [cmds] &Kn [cmds]

  Description:   Enables flow control options

    Command                              Function

      &K0        Flow control disabled

      &K3        RTS/CTS flow control enabled

      &K4        XON/XOFF flow control enabled

      &K5        Transparent XON/XOFF flow control enabled

      &K6        RTS/CTS & XON/XOFF flow control enabled

                                 LINE TYPE

  Type:          Configuration

  Format:        AT [cmds] &Ln [cmds]

  Description:   Command nonfunctional

    Command                             Line Type

      &L0        Returns OK

                                  ON-LINE

  Type:           Immediate

  Format:         AT [cmds] On [cmds]

  Description:    Controls on-line command (data transmission) state
                  options.

            Note: The O command must be placed at the end of the command
            string.

     Command                             Function

       O0         On-line command mode with no retraining enabled

       O1         On-line command mode with long retrain sequence enabled

       O2         On-line command mode with short retrain sequence
                  enabled

                            REPORT INFORMATION

  Type:          Immediate

  Format:        AT [cmds] In [cmds]

  Description:   Displays information requested

    Command                              Function

       I0        Reports product code

       I1        Reports hardware variation code

       I2        Reports DSP firmware revision

       I3        Reports modem firmware revision information

       I4        Reports response programmed by modem manufacturer

                               SPEAKER MODE

  Type:          Configuration

  Format:        AT [cmds] Mn [cmds]

  Description:   Selects various speaker options

    Command                              Function

       M0        Speaker disabled

       M1        Speaker enabled until carrier signal detected

       M2        Speaker enabled

                                TEST MODES

  Type:          Immediate

  Format:        AT [cmds] &Tn

  Description:   Selects test options

    Command                              Function

      &T0        End current test

      &T1        Begin local analog loopback test

                             TRANSMIT CARRIER

  Type:           Configuration

  Format:         AT [cmds] Cn [cmds]

  Description:    Controls the transmit carrier switching. Command
                  nonfunctional

     Command                             Function

       C1         Returns OK message

                            EXTENDED AT COMMANDS

                               CONNECT MODE

  Type:          Configuration

  Format:        AT [cmds] \Nn [cmds]

  Description:   Controls the type of connection the modem will operate
                 in

    Command                              Function

      \N0        Normal mode enabled

      \N1        Normal mode enabled

      \N2        Reliable mode enabled

      \N3        Auto-reliable mode enabled

      \N4        V.42 reliable mode enabled

      \N5        MNP reliable mode enabled



