
ACTION WELL DEVELOPMENT, LTD.

AC-5618 (REV. 1.0)

Card Type                    Modem
Chipset                      Unidentified
I/O Options                  Audio in - CD-ROM, speaker connector, line
                             in, line out, audio in,

                             audio out, microphone in
Maximum Modem Rate           56.0Kbps
Maximum Fax Rate             14.4Kbps
Fax Class                    Class I
Modem Modulation Protocol    Bell 103/212A

                             ITU-T V.22bis,V.32, V.32bis, V.34, V.34bis,
                             V.90
Fax Modulation Protocol      ITU-T V.17
Error Correction/Compression MNP5, V.42, V.42bis
Data Bus                     16-bit ISA

[Image]

                                CONNECTIONS

         Function            Label            Function             Label

  Line in                        CN1       Audio out                CN5

  Line out                       CN2       Audio in - CD-ROM        CN6

  Microphone in                  CN3       Audio in - CD-ROM        CN7

  Audio in                       CN4

                           SUPPORTED COMMAND SET

                             Basic AT Commands

  AT, +++, A/

  A, E, H, M, O, P, Q, T, V

  &C, &P, &V, &W, &Z

                           Extended AT Commands

  \A, \B, \N

  %C, %E

                                S Registers

  S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12

                             Special Commands

  +MS, #CID

                              Voice Commands

  #TL, #VBT, #VRA, #VRX, #VSD, #VSP, #VSS, #VTD, #VTS, #VTX, #SPK

  Note:     See MHI Help File for full command documentation. Further
            information on S-registers is currently unavailable

                         Proprietary AT Command Set

                            AUTO-MODE DETECTION

  Type:                  Configuration

  Format:                AT [cmds] Nn [cmds]

  Description:           Selects various options for the automatic
                         detection and negotiation of protocols during
                         the handshake process if the modem is
                         communicating with a remote modem of dissimilar
                         speed.

        Command                              Function

          N0             Auto-mode detection disabled. Handshake begins
                         at line speed designated by the S32 register

          N1             Auto-mode detection enabled. Handshake conducted
                         according to the automode algorithm supported by
                         the modem

                          COMMUNICATION PROTOCOLS

  Type:          Configuration

  Format:        AT [cmds] Bn [cmds]

  Description:   Selects the communication protocol for data calls

    Command                              Protocol

       B0        ITU-T V.22 at 1200bps

                                COMPRESSION

  Type:           Configuration

  Format:         AT [cmds] &Kn [cmds]

  Description:    Selects data compression

    Command                              Function

      &K0         Data compression disabled

      &K1         MNP5 enabled

      &K2         V.42bis enabled

      &K3         MNP5 and V.42bis; or data compression and correction
                  enabled

                       CONNECT MESSAGE SPEED SOURCE

  Type:          Configuration

  Format:        AT [cmds] &En [cmds]

  Description:   Selects source for speed field in CONNECT message

    Command                              Function

      &E0        DCE speed field

      &E1        DTE speed field

                             CONNECT MESSAGES

  Type:                 Configuration

  Format:               AT [cmds] &An [cmds]

  Description:          Selects the format of CONNECT messages

       Command                              Function

         &A0            CONNECT only

         &A1            Modulation indicator added to CONNECT message

         &A2            Error detection and data compression indicators
                        added to CONNECT message

         &A3            Modulation, error detection and data compression
                        indicators added to CONNECT message





                           DATA SET READY (DSR)

  Type:          Configuration

  Format:        AT [cmds] &Sn [cmds]

  Description:   Selects DSR options

    Command                              Function

      &S0        DSR forced high

      &S1        DSR high only while modem is handshaking or connected

                         DATA TERMINAL READY (DTR)

  Type:          Configuration

  Format:        AT [cmds] &Dn [cmds]

  Description:   Selects modem response to DTR

    Command                              Function

      &D0        DTR forced high

      &D1        DTR toggle causes online command mode

      &D2        Normal DTR operations

      &D3        Resets on receipt of DTR

                           DEFAULT CONFIGURATION

  Type:          Configuration

  Format:        AT [cmds] Yn [cmds]

  Description:   Selects the default user defined configuration

  Note:          Does not load configuration

    Command                              Function

       Y0        Select user template 0

       Y1        Select user template 1

       Y2        Select factory setting 0

       Y3        Select factory setting 1

                                   DIAL

  Type:                  Immediate

  Format:                AT [cmds] D<#> [cmds]

  Description:           Dials telephone number according to any
                         modifiers included in the string

  Note:                  Any combination of modifiers can be used to
                         produce the desired dial functions in sequence.

        Command                              Function

          DL             Re-dial last number

          DP             Pulse dialing enabled

         DS=n            Dial stored telephone number n

          DT             Tone dialing enabled/Pulse dialing disabled

          DW             Dialing resumed following dial tone detection

          D,             Dialing paused for amount of time specified in
                         S8 register

          D@             Wait for Quite Answer function enabled. Modem
                         waits until a "quiet answer," a ring-back signal
                         followed by silence up to the time specified in
                         S7, is received prior to executing the rest of
                         the dial string.

          D!             Flash function initiated. Modem commanded to go
                         off-hook for specified time before returning
                         on-hook.

          D;             Modem returned to idle state after dialing. The
                         semicolon can only be placed at the end of the
                         dial command.





                          FACTORY DEFAULT PROFILE

  Type:             Configuration

  Format:           AT [cmds] &Fn [cmds]

  Description:      Sets values in active profile to values found in the
                    default profile

     Command                              Function

       &F0          Restore factory configuration 0

       &F1          Restore factory configuration 1

                               FLOW CONTROL

  Type:          Configuration

  Format:        AT [cmds] &Hn [cmds]

  Description:   Enables/disables flow control

    Command                              Function

      &H0        Flow control disabled

      &H1        RTS to CTS flow control enabled

                            REPORT INFORMATION

  Type:          Immediate

  Format:        AT [cmds] In [cmds]

  Description:   Displays information requested

    Command                              Function

       I1        Reports manufacturer and model name

       I2        Reports software version and provider

       I3        Reports vendor/chip ID

       I4        Reports stored and active profile

       I5        Reports stored and active profile

       I6        Reports stored and active profile

       I7        Reports stored telephone numbers

                                  RTS/CTS

  Type:          Configuration

  Format:        AT [cmds] &Rn [cmds]

  Description:   Selects RTS/CTS options

    Command                              Function

      &R0        RTS is ignored

      &R1        Modem recieves data only on RTS

                     SELECT CALL PROGRESS RESULT CODES

  Type:                Configuration

  Format:              AT [cmds] Xn [cmds]

  Description:         Enables selection of tone detection and associated
                       result code format options

       Command                             Function

         X0            Busy and dial tone detection disabled; result
                       codes 0 - 4 enabled.

         X1            Busy and dial tone detection disabled; result
                       codes 0 - 5 & 9 - 1212 enabled.

         X2            Busy tone detection disabled, dial tone detection
                       enabled; result codes 0 - 6 &

                       9 - 1212 enabled.

         X3            Busy tone detection enabled, dial tone detection
                       disabled; result codes 0 - 5,

                       7 - 1212 enabled.

         X4            Busy and dial tone detection enabled; result codes
                       0 - 1212 enabled.





                                SOFT RESET

  Type:           Immediate

  Format:         AT [cmds] Zn [cmds]

  Description:    Restores modem profiles previously saved in
                  non-volatile RAM

    Command                              Function

       Z0         Restore default user template as defined by Yn

       Z1         Restore user template 0

       Z2         Restore user template 1

       Z3         Restore factory setting 0

       Z4         Restore factory setting 1

                              SPEAKER VOLUME

  Type:          Configuration

  Format:        AT [cmds] Ln [cmds]

  Description:   Controls speaker volume

    Command                              Function

       L0        Low volume setting

       L1        Low volume setting

       L2        Medium volume setting

       L3        Highest volume setting

                                TEST MODES

  Type:          Immediate

  Format:        AT [cmds] &Tn

  Description:   Selects test options

    Command                              Function

      &T0        TBD

      &T1        TBD

      &T2        TBD

      &T3        TBD

                          EXTENDED AT COMMAND SET

                                BREAK TYPE

  Type:           Configuration

  Format:         AT [cmds] \Kn [cmds]

  Description:    Configures action of break signal

    Command                              Function

      \K0        Online command mode enabled, send no break to remote
                 modem

      \K1        Break sent to remote modem and buffered cleared

      \K2        Online command mode enabled, send no break to remote
                 modem

      \K3        Send break to remote modem immediately

      \K4        Online command mode enabled, send no break to remote
                 modem

      \K5        Send break with transmitted data





                               VOICE COMMANDS

                             INACTIVITY TIMER

  Type:                Configuration

  Format:              AT [cmds] #VIT=n [cmds]

  Range:               0-255

  Unit:                .1ms

  Description:         Maximum duration of voice inactivity allowed prior
                       to initiating hang-up process.

                              MODE SELECTION

  Type:          Immediate

  Format:        AT [cmds] #CLS=n [cmds]

  Description:   Selects which mode the modem will operate in.

    Command                              Function

     #CLS=0      Modem will operate in data mode.

     #CLS=1      Modem will operate in fax class I mode.

     #CLS=8      Modem will operate in voice mode.

                                RECORD GAIN

  Type:          Configuration

  Format:        AT [cmds] #RG=hhhh [cmds]

  Range:         0000 - 7FFF

  Unit:          Unidentified (hexadecimal)

  Description:   Sets the record gain. #RG? queries value

                      VOICE - LOCAL SERIAL PORT SPEED

  Type:           Configuration

  Format:         AT [cmds] #BDR=n [cmds]

  Range:          0-48

  Unit:           2400bps

  Description:    Sets the speed of the local serial port when in voice
                  mode.

                               VOICE DEVICE

  Type:                Configuration

  Format:              AT [cmds] #VLS=n [cmds]

  Description:         Selects the I/O device for the DSP chip.

  Note:                VLS? Queries current setting. #VLS=? Command will
                       display the available options.

       Command                              Function

       #VLS=0          Telephone line and handset used for voice I/O.

       #VLS=2          Internal speaker only used for voice I/O.

       #VLS=3          External microphone only used for voice I/O.

       #VLS=4          Telephone line and handset used for voice I/O;
                       internal speaker enabled.

       #VLS=6          Speakerphone used for voice I/O.

                             VOICE PARAMETERS

  Type:          Configuration

  Format:        AT [cmds] #VIP [cmds]

  Description:   Initializes voice parameters





                          VOICE RING DETECT TIME

  Type:                  Configuration

  Format:                AT [cmds] #VRN=n [cmds]

  Default:               Unidentified

  Range:                 0-255

  Unit:                  .1ms

  Description:           Sets the maximum time the modem will wait for
                         the remote station to ring before it assumes
                         that it went off-hook before it rang.

                           VOICE SAMPLE QUALITY

  Type:                  Configuration

  Format:                AT [cmds] #VBS=n [cmds]

  Description:           Selects the number of bits per sample that the
                         modem records.

  Note:                  This modem may not support all options listed
                         below. The #VBS? Command will display the
                         available options.

        Command                              Function

         #VBS=2          Modem records 2 bits per sample in ADPCM
                         encoding.

         #VBS=4          Modem records 4 bits per sample in ADPCM
                         encoding.

         #VBS=8          Modem records 8 bits per sample in PCM encoding.

        #VBS=16          Modem records 16 bits per sample in PCM
                         encoding.

                            VOICE SAMPLING RATE

  Type:                Configuration

  Format:              AT [cmds] #VSR=n [cmds]

  Description:         Sets the sampling rate used when recording voice
                       signals. #VSR? queries settings

       Command                              Function

      #VSR=7200        Selects a sampling rate of 7.2KHz.

      #VSR=8000        Selects a sampling rate of 8.0KHz.

                             VOICE TIMING MARK

  Type:          Configuration

  Format:        AT [cmds] #VTM=n [cmds]

  Range:         1-10

  Unit:          1ms

  Description:   Configures timing mark placement.

                            VOICE VOLUME LEVEL

  Type:          Configuration

  Format:        AT [cmds] #VGT=n [cmds]

  Range:         0-255

  Description:   Sets the volume level when playing back audio signals.

