
WISECOM, INC.

WS-5614JS3/ES3 (INTERNAL)

Card Type                    Modem
Chip Set                     Unidentified
I/O Options                  Line out, line in, speaker out, microphone in
Maximum Modem Rate           56Kbps
Maximum Fax Rate             14.4Kbps
Data Modulation Protocol     Bell 103/212A

                             ITU-T V.22, V.22bis, V.32, V.32bis, V.34,
                             56Kflex
Fax Modulation Protocol      ITU-T V.17, V.21 CH.2, V.27ter, V.29
Error Correction/Compression MNP5, V.42, V.42bis
Fax Class                    Class I
Data Bus                     8-bit ISA

[Image]

                                CONNECTIONS

        Function           Label             Function              Label

  Line out (RJ-11)              CN1      Speaker out                CN3

  Line in (RJ-11)               CN2      Microphone in              CN4

                               PLUG & PLAY

         Setting                   JP3                      JP4

  ? Plug & play enabled     Pins 1 & 2 closed        Pins 1 & 2 closed

  Plug & play disabled      Pins 2 & 3 closed        Pins 2 & 3 closed

            SERIAL PORT ADDRESS

    Setting        SW1/1          SW1/2

  COM1 (3F8h)        On            On

  COM2 (2F8h)       Off            On

  COM3 (3E8h)        On            Off

  COM4 (2E8h)       Off            Off

                      INTERRUPT

       IRQ          SW1/3    SW1/4    SW1/5    SW1/6

        2            On       Off      Off      Off

        3            Off      On       Off      Off

        4            Off      Off       On      Off

        5            Off      Off      Off       On



                           SUPPORTED COMMAND SET

                             Basic AT Commands

  AT, +++, A/

  A, B, E, H, V

  &C, &M, &P, &T, &V, &W, &X, &Y, &Z

                           Extended AT Commands

  %C, %E, %L, %Q

  \A, \B, \K, \N

                             Special Commands



                                S Registers

  S0, S1, S2, S3, S4, S5, S6, S7, S8, S9,S10, S11, S12, S14, S16, S18,
  S21, S22, S23, S24, S25

  S26, S27, S29, S30, S31, S32, S33, S36, S37, S38, S39, S40, S41, S46,
  S48, S82, S91, S92, S95

  Note: See MHI Help File for full command documentation.

                         PROPRIETARY AT COMMAND SET

                            COMMUNICATIONS MODE

  Type:                  Configuration

  Format:                AT [cmds] &Qn [cmds]

  Description:           Selects communications mode options

        Command                                Mode

          &Q0            Asynchronous mode, serial port speed follows
                         connect speed.

          &Q1            Asynchronous off-line command mode and
                         synchronous connect mode.

          &Q2            Asynchronous off-line command mode - modem
                         autodials first number in directory, then
                         synchronous connect mode.

          &Q3            Asynchronous off-line command mode on low DTR,
                         synchronous connect mode on high DTR.

         ? &Q5           Error correction mode

          &Q6            Buffered asynchronous mode

                           DATA SET READY (DSR)

  Type:          Configuration

  Format:        AT [cmds] &Sn [cmds]

  Description:   Selects DSR options

    Command                              Function

      &S0        DSR forced high

      &S1        DSR high only while modem is handshaking or connected

                                     DATA TERMINAL READY (DTR)

  Type:              Configuration

  Format:            AT [cmds] &Dn [cmds]

  Description:       Selects modem response to DTR

      Command                                            Mode

        &D0           DTR ignored

        &D1           DTR toggle causes online command mode

       ? &D2          DTR toggle causes modem to go on-hook

        &D3           Modem reset on DTR toggle



                                   DIAL

  Type:              Immediate

  Format:            AT [cmds] D<#> [cmds]

  Description:       Dials telephone number according to any modifiers
                     included in the string

                          FACTORY DEFAULT PROFILE

  Type:             Configuration

  Format:           AT [cmds] &F [cmds]

  Description:      Sets values in active profile to values found in the
                    default profile

       &F0          Load factory configuration 0

       &F1          Load factory configuration 1

                               FLOW CONTROL

  Type:          Configuration

  Format:        AT [cmds] &Kn [cmds]

  Description:   Enables flow control options

    Command                              Function

      &K0        Flow control disabled

      &K3        RTS/CTS flow control enabled

      &K4        XON/XOFF flow control enabled

      &K5        Transparent XON/XOFF flow control enabled

     ? &K6       Both RTS/CTS & XON/XOFF flow control enabled

                                GUARD TONE

  Type:           Configuration

  Format:         AT [cmds] &Gn [cmds]

  Description:    Commands the modem to transmit a guard tone in
                  V.22/V.22bis

            Note: Used primarily for international data transmission

    Command                              Function

     ? &G0        Guard tone disabled

      &G1         550Hz guard tone enabled

      &G2         1800Hz guard tone enabled

                            REPORT INFORMATION

  Type:          Immediate

  Format:        AT [cmds] In [cmds]

  Description:   Displays information requested

    Command                              Function

       I0        Reports modem model and speed

       I1        Reports ROM checksum

       I2        Tests and reports ROM checksum

       I3        Reports product ID string

       I6        Reports diagnostic information

       I7        Reports product configuration



                        RESTORE PROFILE ON POWER-UP

  Type:              Configuration

  Format:            AT [cmds] Yn [cmds]

  Description:       Restores a selected profile to default profile on
                     power-up (hard reset)

      Command                             Function

       ? Y0          Restore stored profile 0 on power-up

        Y1           Restore stored profile 1 on power-up

        Y2           Load factory default configuration 0 on power-up

        Y3           Load factory default configuration 1 on power-up

        Y4           Load factory default configuration 2 on power-up

                                  RTS/CTS

  Type:           Configuration

  Format:         AT [cmds] &Rn [cmds]

  Description:    Selects RTS/CTS options

    Command                              Function

      &R0         CTS follows RTS in data mode; RTS is ignored in command
                  mode.

     ? &R1        CTS forced high, RTS is ignored.

                                SOFT RESET

  Type:                Configuration

  Format:              AT [cmds] Zn [cmds]

  Description:         Restores modem profiles previously stored in
                       non-volatile RAM using the &W command

       Command                              Function

         ? Z1          Restore stored profile 0

          Z2           Restore stored profile 1

          Z3           Load factory default configuration 0

          Z4           Load factory default configuration 1

          Z5           Load factory default configuration 2

                               SPEAKER MODE

  Type:          Configuration

  Format:        AT [cmds] Mn [cmds]

  Description:   Selects various speaker options

    Command                              Function

       M0        Speaker disabled

       M1        Speaker enabled until carrier signal detected

                              SPEAKER VOLUME

  Type:          Configuration

  Format:        AT [cmds] Ln [cmds]

  Description:   Controls speaker volume

    Command                              Function

       L0        Low volume setting

       L1        Low volume setting

      ? L2       Medium volume setting

       L3        Highest volume setting



                          EXTENDED AT COMMAND SET

                           MODULATION SELECTION

  Type:                  Configuration

  Format:                AT [cmds] +MS=x,y,z,a,b,c [cmds]

  Description:           Sets options for active protocol; the transfer
                         rates specified by z and a must be valid for the
                         protocol selected.

        Command                             Function

          x=0            V.21

          x=1            V.22

          x=2            V.22bis

          x=3            V.23

          x=9            V.32

         x=10            V.32bis

         x=11            V.34, K56flex

         x=64            Bell 103

         x=69            Bell 212A

          y=0            Automode disabled

          y=1            Auto-detect highest speed enabled

       z, a=300          Set minimum or maximum transfer rate at 300bps,
                         respectively.

       z, a=1200         Set minimum or maximum transfer rate at 1200bps,
                         respectively.

       z, a=2400         Set minimum or maximum transfer rate at 2400bps,
                         respectively.

       z, a=4800         Set minimum or maximum transfer rate at 4800bps,
                         respectively.

       z, a=7200         Set minimum or maximum transfer rate at 7200bps,
                         respectively.

       z, a=9600         Set minimum or maximum transfer rate at 9600bps,
                         respectively.

      z, a=12000         Set minimum or maximum transfer rate at
                         12000bps, respectively.

      z, a=14400         Set minimum or maximum transfer rate at
                         14400bps, respectively.

      z, a=16800         Set minimum or maximum transfer rate at
                         16800bps, respectively.

      z, a=19200         Set minimum or maximum transfer rate at
                         19200bps, respectively.

      z, a=21600         Set minimum or maximum transfer rate at
                         21600bps, respectively.

      z, a=24000         Set minimum or maximum transfer rate at
                         24000bps, respectively.

      z, a=26400         Set minimum or maximum transfer rate at
                         26400bps, respectively.

      z, a=28800         Set minimum or maximum transfer rate at
                         28800bps, respectively.

      z, a=33600         Set minimum or maximum transfer rate at
                         33600bps, respectively.

          b=0            m -law encoding

          b=1            A -law encoding

          c=0            Robbed bit signaling disabled

          c=1            Robbed bit signaling enabled

                            S(Status) REGISTERS

                         CONNECTION FAILURE CODES

  Type:               Register

  Format              AT [cmds] S86? [cmds]

  Description:        Reports codes which correspond to the possible
                      causes of a connection failure

       Value                                Meaning

         0            Normal hang up

         4            Carrier signal lost

         5            No error-control detected for remote modem during
                      feature negotiation

         9            No common protocol found

         12           No failure - remote modem disconnected normally

         13           Remote modem failed to respond after 10
                      re-transmissions same message

         14           Violation of negotiated protocol caused failure

