
PHILIPS CONSUMER ELECTRONICS, CO.

PCA11IM (JUMPER VER.)

Card Type                    Modem
Chip Set                     Unidentified
I/O Options                  Line out, line in, microphone in, speaker out
Maximum Modem Rate           14.4Kbps
Maximum Fax Rate             14.4Kbps
Data Modulation Protocol     Bell 103/212A

                             ITU-T V.22, V.22bis, V.23, V.32, V.32bis
Fax Modulation Protocol      ITU-T V.17, V.27ter, V.29
Error Correction/Compression MNP5, V.42, V.42bis
Fax Class                    Class I & II
Data Bus                     8-bit ISA

[Image]

                                CONNECTIONS

        Function           Label             Function              Label

  Line out (RJ-11)              CN1      Speaker out                CN3

  Line in (RJ-11)               CN2      Microphone in              CN4

           SERIAL PORT ADDRESS

    Setting        JP8/A        JP8/B

  COM1 (3F8h)     Closed       Closed

  COM2 (2F8h)      Open        Closed

  COM3 (3E8h)     Closed        Open

  COM4 (2E8h)      Open         Open

                           INTERRUPT

       Setting           JP8/C      JP8/D     JP8/E     JP8/F

         IRQ2            Closed      Open      Open      Open

         IRQ3             Open      Closed     Open      Open

         IRQ4             Open       Open     Closed     Open

         IRQ5             Open       Open      Open     Closed



                           SUPPORTED COMMAND SET

                             Basic AT Commands

  AT, +++, A/

  A, E, H, M, O, P, T, V, X, Y, Z

  &C, &F, &G, &M, &T, &V, &W, &X, &Y, &Z

                           Extended AT Commands

  %A, %C, %E, %Q

  \A, \B, \C, \G, \J, \K, \Q, \T, \X

                                S Registers

  S0, S1, S2, S3, S4, S5, S6, S7, S8, S9,S10, S11, S12, S14, S16, S18,
  S21, S22, S23, S25

  S26, S27, S30, S91

  Note: See MHI Help File for full command documentation.

                         PROPRIETARY AT COMMAND SET

                            AUTO-MODE DETECTION

  Type:                  Configuration

  Format:                AT [cmds] Nn [cmds]

  Description:           Selects various options for the automatic
                         detection and negotiation of protocols during
                         the handshake process if the modem is
                         communicating with a remote modem of dissimilar
                         speed.

        Command                              Function

          N0             Auto-mode detection disabled; handshake begins
                         at line speed designated by the %B command

          N1             Auto-mode detection enabled; handshake begins at
                         line speed designated by the %B command and DTE
                         speed

                          COMMUNICATION PROTOCOLS

  Type:                  Configuration

  Format:                AT [cmds] Bn [cmds]

  Description:           Selects the communication protocol for data
                         calls

            Note: The B command allows the simultaneous selection of more
            than one suffix, enabling multiple protocols.

        Command                              Protocol

          B0             ITU-T V.22 at 1200bps

          B1             Bell 212A at 1200bps

          B2             ITU-T V.22 at 75/1200Kbps in originate mode,
                         1200/75Kbps in answer mode

                           DATA SET READY (DSR)

  Type:          Configuration

  Format:        AT [cmds] &Sn [cmds]

  Description:   Selects DSR options

    Command                              Function

      &S0        DSR forced high

      &S1        DSR high only while modem is handshaking or connected



                         DATA TERMINAL READY (DTR)

  Type:          Configuration

  Format:        AT [cmds] &Dn [cmds]

  Description:   Selects modem response to DTR

    Command                              Function

      &D0        DTR ignored

      &D1        DTR toggle causes online command mode

      &D2        DTR toggle causes modem to go on-hook

      &D3        Modem reset on DTR toggle

                                   DIAL

  Type:                  Immediate

  Format:                AT [cmds] D<#> [cmds]

  Description:           Dials telephone number according to any
                         modifiers included in the string

  Note:                  Any combination of modifiers can be used to
                         produce the desired dial functions in sequence.

        Command                              Function

          DP             Pulse dialing enabled

          DR             Answer mode enabled; originate mode disabled
                         following handshake initiation.

         DS=n            Dial stored telephone number n

          DT             Tone dialing enabled/Pulse dialing disabled

          DW             Dialing resumed following dial tone detection

          D,             Dialing paused for amount of time specified in
                         S8 register

          D!             Flash function initiated. Modem commanded to go
                         off-hook for specified time before returning
                         on-hook.

          D@             Wait for Quite Answer function enabled. Modem
                         waits until a "quiet answer," a ring-back signal
                         followed by silence up to the time specified in
                         S7, is received prior to executing the rest of
                         the dial string.

          D^             Data calling tone enabled

          D;             Modem returned to idle state after dialing. The
                         semicolon can only be placed at the end of the
                         dial command.

                               FLOW CONTROL

  Type:          Configuration

  Format:        AT [cmds] &Kn [cmds]

  Description:   Enables flow control options

    Command                              Function

      &K0        Flow control disabled

      &K3        RTS/CTS flow control enabled

      &K4        XON/XOFF flow control enabled

                                 LINE TYPE

  Type:          Configuration

  Format:        AT [cmds] &Ln [cmds]

  Description:   Selects line type

    Command                             Line Type

      &L0        Switched line (PSTN/Dial-up)

      &L1        Leased line

      &L2        Power-on leased line



                            PULSE DIALING RATIO

  Type:          Configuration

  Format:        AT [cmds] &Pn [cmds]

  Description:   Selects pulse dial make/break ratio

    Command                              Function

      &P0        39/61ms at 10pps (North America)

      &P1        33/67ms at 10pps (Europe)

      &P2        39/61ms at 20pps

                            REPORT INFORMATION

  Type:          Immediate

  Format:        AT [cmds] In [cmds]

  Description:   Displays information requested

    Command                              Function

       I0        Reports product code

       I1        Reports ROM checksum

       I2        Tests and reports ROM checksum

       I3        Reports model ID & firmware ID

       I5        Reports country code

                               RESULT CODES

  Type:               Configuration

  Format:             AT [cmds] Qn [cmds]

  Description:        Enables modem to send result codes to the DTE

      Command                              Function

         Q0           Result code sending enabled

         Q1           Result code sending disabled

         Q2           "Ring" result code disabled. In answer mode;
                      CONNECT and NO CARRIER disabled

                              SPEAKER VOLUME

  Type:          Configuration

  Format:        AT [cmds] Ln [cmds]

  Description:   Controls speaker volume

    Command                              Function

       L0        Low volume setting

       L1        Low volume setting

       L2        Medium volume setting

       L3        Highest volume setting



                          EXTENDED AT COMMAND SET

                             CONNECTION SPEED

  Type:          Configuration

  Format:        AT [cmds] %Bn [cmds]

  Description:   Selects maximum modem connection speed

    Command                              Function

     %B300       300bps

     %B1200      1200bps

     %B2400      2400bps

     %B4800      4800bps

     %B7200      7200bps

     %B9600      9600bps

    %B12000      12.0Kbps

    %B14400      14.4Kbps

                               CONNECT MODE

  Type:          Configuration

  Format:        AT [cmds] \Nn [cmds]

  Description:   Controls the type of connection the modem will operate
                 in

    Command                              Function

      \N0        Normal mode enabled

      \N1        Direct mode enabled

      \N2        MNP reliable mode enabled

      \N3        Auto-reliable mode enabled

      \N4        V.42 reliable mode enabled

      \N5        V.42/Normal mode enabled

      \N6        V.42/MNP mode enabled

      \N7        MNP/Normal mode enabled

                           EXTENDED RESULT CODES

  Type:            Configuration

  Format:          AT [cmds] \Vn [cmds]

  Description:     Selects extended result codes

     Command                             Function

       \V0         DCE speed displayed. Extended result codes disabled

       \V1         DCE speed; simple reliable mode extended result codes
                   enabled

       \V2         DCE speed; detailed reliable mode extended result
                   codes enabled

       \V3         DTE speed only

                            S(status) -REGISTERS

                     AUTO-RELIABLE FALLBACK CHARACTER

  Type:            Register

  Format:          AT [cmds] S29=n [cmds]

  Range:           0-127

  Unit:            ASCII

  Description:     Sets the character used as the auto-reliable fallback
                   character



                          BIT-MAPPED REGISTER S15

  Format:        AT [cmds] S15=n [cmds]

  Range:         0-255

  Unit:          Bit-mapped

  Description:   Controls MNP options, break types, DTE rate adjustments.

  Note:          Further information is currently unavailable

                          BIT-MAPPED REGISTER S17

  Format:          AT [cmds] S17=n [cmds]

  Range:           0-255

  Unit:            Bit-mapped

  Description:     Controls relaible mode, data compression, and extended
                   responses

  Note:            Further information is currently unavailable

                          BIT-MAPPED REGISTER S19

  Format:        AT [cmds] S19=n [cmds]

  Range:         0-255

  Unit:          Bit-mapped

  Description:   Determines flow control, echo, XON/XOFF pass-through

  Note:          Further information is currently unavailable

                          BIT-MAPPED REGISTER S20

  Format:        AT [cmds] S20=n [cmds]

  Range:         0-255

  Unit:          Bit-mapped

  Description:   Sets PC/NEC baud rate options, guard tones

  Note:          Further information is currently unavailable

                          BIT-MAPPED REGISTER S24

  Format:         AT [cmds] S24=n [cmds]

  Range:          0-255

  Unit:           Bit-mapped

  Description:    Controls make/break ratio, auto retrain, V.34/VFC, auto
                  mode

  Note:           Further information is currently unavailable

                          BIT-MAPPED REGISTER S28

  Format:        AT [cmds] S28=n [cmds]

  Range:         Unidentified

  Unit:          Bit-mapped

  Description:   Determine DCE rate

  Note:          Further information is currently unavailable

                                SLEEP TIMER

  Type:                   Register

  Format                  AT [cmds] S13=n [cmds]

  Range:                  0-255

  Unit:                   1 second

  Description:            Maximum duration of DTE and DCE inactivity
                          allowed prior to initiating low-power sleep
                          mode.



