
CARDINAL TECHNOLOGIES, INC

9600BPS V.32BIS DIGITAL

Card Type                    Modem
Chip Set                     Unidentified
I/O Options                  Line in, line out
Maximum Modem Rate           9600bps
Maximum Fax Rate             9600bps
Data Modulation Protocol     Bell 103/212A

                             ITU-T V.21, V.22, V.22bis, V.32
Fax Modulation Protocol      ITU-T V.21 CH 2, V.27ter, V.29
Error Correction/Compression MNP5, V.42, V.42bis
Fax Class                    Class I & II
Data Bus                     8-bit ISA

[Image]

                                CONNECTIONS

         Function           Label             Function             Label

  Line out (RJ-11)               CN1      Line in (RJ-11)           CN2

              SERIAL PORT ADDRESS

     Setting          JP1/A          JP1/B

   COM1 (3F8h)       Closed         Closed

   COM2 (2F8h)       Open          Closed

   COM3 (3E8h)       Closed          Open

   COM4 (2E8h)        Open           Open

                           INTERRUPT

       Setting           JP1/C      JP1/D     JP1/E     JP1/F

         IRQ2             Open       Open      Open     Closed

         IRQ3            Open      Closed     Open      Open

         IRQ4            Closed      Open      Open      Open

         IRQ5             Open       Open     Closed     Open



                         SUPPORTED COMMAND SET

                           Basic AT Commands

  AT, +++, A/

  A, B, E, H, O, Q, M, V

  &C, &F, &V

                          Extended AT Commands

  \N

                              S Registers

  S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S18, S14, S16, S18



                            Special Commands

  Note: Please see MHI Help file for full command documentation.

                         Proprietary AT Command Set

                           DATA SET READY (DSR)

  Type:          Configuration

  Format:        AT [cmds] &Sn [cmds]

  Description:   Selects DSR options

    Command                              Function

      &S0        DSR forced high

      &S1        DSR high only while modem is handshaking or connected

                         DATA TERMINAL READY (DTR)

  Type:          Configuration

  Format:        AT [cmds] &Dn [cmds]

  Description:   Selects modem response to DTR

    Command                              Function

      &D0        DTR ignored

      &D1        DTR toggle causes online command mode

      &D2        DTR toggle causes modem to go on-hook

      &D3        Modem reset on DTR toggle

                                   DIAL

  Type:                  Immediate

  Format:                AT [cmds] D<#> [cmds]

  Description:           Dials telephone number according to any
                         modifiers included in the string

  Note:                  Any combination of modifiers can be used to
                         produce the desired dial functions in sequence.

        Modifier                             Function

           DP            Pulse dialing enabled

           DR            Answer mode enabled, originate mode disabled
                         following handshake initiation

           DT            Tone dialing enabled

           DW            Dialing resumed following dial tone detection

           D,            Dialing paused for amount of time specified in
                         S8 register

           D!            Modem commanded to go off-hook for .5 seconds
                         before returning on-hook

           D@            Wait for quiet answer

           D;            Modem returned to command state after dialing



                           EXTENDED RESULT CODES

  Type:          Configuration

  Format:        AT [cmds] Wn [cmds]

  Description:   Enables selection of additional result codes

    Command                              Function

       W0        Enables CONNECT result codes to report DTE to DCE speed

       W1        Enables CONNECT result codes to report error correction

                               FLOW CONTROL

  Type:          Configuration

  Format:        AT [cmds] &Kn [cmds]

  Description:   Enables flow control options

    Command                              Function

      &K0        Flow control disabled

      &K3        RTS/CTS flow control enabled

      &K4        XON/XOFF flow control enabled

      &K5        Transparent XON/XOFF flow control enabled

                            PULSE DIALING RATIO

  Type:          Configuration

  Format:        AT [cmds] &Pn [cmds]

  Description:   Selects pulse dial make/break ratio

    Command                              Function

      &P0        39/61ms at 10pps (North America)

      &P1        33/67ms at 10pps (Europe)

      &P2        39/61ms at 20pps

                            REPORT INFORMATION

  Type:          Immediate

  Format:        AT [cmds] In [cmds]

  Description:   Displays information requested

    Command                              Function

       I0        Reports product code

       I1        Reports ROM checksum

       I2        Tests and reports ROM checksum

       I3        Reports modem capabilities

                     SELECT CALL PROGRESS RESULT CODES

  Type:                  Configuration

  Format:                AT [cmds] Xn [cmds]

  Description:           Enables selection of tone detection and
                         associated result code format options

        Command                              Function

           X0            Busy and dial tone detection disabled; result
                         codes 0 - 4, 8 enabled.

           X1            Busy and dial tone detection disabled; result
                         codes 0 - 5, 8 & 10 - 15 enabled.

           X2            Busy tone detection disabled, dial tone
                         detection enabled; result codes 0 - 6, 8 & 10 -
                         15 enabled.

           X3            Busy tone detection enabled, dial tone detection
                         disabled; result codes 0 - 8, & 10 - 15 enabled.

           X4            Busy and dial tone detection enabled; result
                         codes 0 - 7 & 10 enabled.

           X5            Busy and dial tone detection enabled; result
                         codes 0 - 4, 6 - 8 enabled.



                                SOFT RESET

  Type:                Immediate

  Format:              AT [cmds] Zn [cmds]

  Description:         Restores modem profiles previously saved in
                       non-volatile RAM using the &W command.

       Command                              Function

          Z0           Restore setting

                          EXTENDED AT COMMAND SET

                                COMPRESSION

  Type:          Configuration

  Format:        AT [cmds] %Cn [cmds]

  Description:   Selects data compression

    Command                              Function

      %C0        Data compression disabled

      %C1        MNP5 enabled

                            S(status) REGISTERS

                              DCE LINE SPEED

  Type:                Register

  Format               AT [cmds] S37=n [cmds]

  Description:         Sets the maximum allowable data exchange rate
                       attempted during handshake process.

       Command                              Function

        S37=0          Current DTE rate

        S37=1          V.21 at 300bps

        S37=2          Bell 103 at 300bps

        S37=5          V.22 at 1200bps

        S37=6          V.22bis at 2400bps

        S37=8          V.32 at 4800bps

        S37=9          V.32 at 9600bps

