
TORNADO CO., LTD

WEBJET 128

Card Type                           ISDN TA
Chip Set                            Unidentified
I/O Options                         RJ-45 ISDN BRI U interface, 9-pin DTE
                                    port, power, microphone in, speaker
                                    out
ISDN Rate                           230.4Kbps
ISDN Modulation Protocol            PPP, MLPPP, V.120
Error Correction/Compression        Unidentified
Data Bus                            External

[Image]

                                CONNECTIONS

           Function             Label           Function            Label

  ISDN BRI interface (RJ-45)     CN1     9-pin DTE port             CN4

  Microphone in                  CN2     Power                      CN5

  Speaker out                    CN3     Power switch               SW1

                             DIAGNOSTIC LED(S)

   LED          Color           Status                Condition

  DATA          Unidentified      On                 DTR is high

  DATA      Unidentified       Blinking      Serial data transfer active

  DATA          Unidentified      Off         Serial data transfer not in
                                                       progress

   B1           Unidentified      On             B-channel 1 data call
                                                      connected

   B1       Unidentified          Off         No activity on B-channel 1

   B2           Unidentified      On             B-channel 2 data call
                                                      connected

   B2       Unidentified          Off         No activity on B-channel 2

   PWR          Unidentified      On                 Power is on

   PWR      Unidentified          Off                Power is off

                SUPPORTED COMMAND SET

                  Basic AT Commands

  AT, +++, A/

  A, E, Q, V, W, X

  &F, &V

                     S Registers

  S0, S2, S3, S4, S5, S7, S25

  Note:

  See MHI Help File for full command documentation.

Proprietary AT Command Set

                            COMMUNICATIONS MODE

  Type:                Configuration

  Format:              AT [cmds] &M n [cmds]

  Description:         Selects communications mode

       Command                                Mode

         &M0           Asynchronous mode

         &M1           Synchronous connect mode and asynchronous off-line
                       command mode.

         &M2           Synchronous connect mode and asynchronous off-line
                       command mode and set DTR high.

                            COMMUNICATIONS MODE

  Type:                  Configuration

  Format:                AT [cmds] &Q n [cmds]

  Description:           Selects communications mode options

        Command                               Mode

          &Q0            Asynchronous mode, serial port speed follows
                         connect speed.

          &Q1            Asynchronous off-line command mode and
                         synchronous connect mode.

          &Q2            Asynchronous off-line command mode - modem
                         autodials first number in directory, then
                         synchronous connect mode.

          &Q3            Asynchronous off-line command mode on low DTR,
                         synchronous connect mode on high DTR.

          &Q4            Auto-synchronous mode

          &Q5            Error correction mode

                         DATA CARRIER DETECT (DCD)

  Type:              Configuration

  Format:            AT [cmds] &C n [cmds]

  Description:       Selects whether the DCD option is enabled or
                     disabled

      Command                             Function

        &C0          DCD enabled

        &C1          DCD enabled after carrier signal detected

        &C2          DCD enabled when on-line, low at loss of carrier,
                     enabled again at idle

                           DATA SET READY (DSR)

  Type:          Configuration

  Format:        AT [cmds] &S n [cmds]

  Description:   Selects DSR options

    Command                              Function

      &S0        DSR forced high

      &S1        DSR high only while modem is connected

      &S2        DSR high only while modem is connected

                         DATA TERMINAL READY (DTR)

  Type:            Configuration

  Format:          AT [cmds] &D n
                   [cmds]

  Description:     Selects modem
                   response to DTR

            Note: The action each variant of &D causes depends on the
            setting of &Q

    &Q Setting             &D0              &D1        &D2         &D3

     &Q0, &Q5           Command 0          Command    Command   Command 4
                                             1          2

       &Q1              Command 2          Command    Command   Command 4
                                             1          2

       &Q2              Command 2          Command    Command   Command 2
                                             2          2

     Command             Function

    Command 0      Modem does not
                   respond to DTR

    Command 1      Modem goes to
                   command mode after
                   DTR goes is off

    Command 2      Modem goes to
                   command mode and
                   disconnects (hangs
                   up) after DTR goes
                   off; Auto-Answer is
                   disabled.

    Command 3      Modem is
                   initialized after
                   DTR goes off

                                   DIAL

  Type:              Immediate

  Format:            AT [cmds] D<#> [cmds]

  Description:       Dials telephone number according to any modifiers
                     included in the string

                               FLOW CONTROL

  Type:          Configuration

  Format:        AT [cmds] &K n [cmds]

  Description:   Enables flow control options

    Command                              Function

      &K0        Flow control disabled

      &K1        RTS to CTS flow control enabled

      &K2        XON/XOFF flow control enabled

      &K3        RTS/CTS flow control enabled

      &K4        XON/XOFF flow control enabled

                               HOOK CONTROL

  Type:          Immediate

  Format:        AT [cmds] H n [cmds]

  Description:   Selects whether the modem is on-hook or off-hook

    Command                              Function

       H0        Modem commanded to go on-hook (hang-up)

                                  ON-LINE

  Type:           Immediate

  Format:         AT [cmds] O n [cmds]

  Description:    Controls on-line command (data transmission) state
                  options.

            Note: The O command must be placed at the end of the command
            string.

     Command                             Function

       O0         On-line command mode with no retraining enabled

                            PROTOCOL SELECTION

  Type:          Configuration

  Format:        AT [cmds] &O n [cmds]

  Description:   Selects active protocol

    Command                                Mode

      &O7        PPP, 1 x B

      &O8        V.14, 1 x B

      &O9        V.110, 1 x B

      &O10       V.120, 1 x B

      &O13       Multi Link V.120, 2 x B

      &O16       GCI-speech, 2 x B

      &O18       GCI-data, 2 x B

      &O27       Multi Link PPP, 2 x B

                            REPORT INFORMATION

  Type:          Immediate

  Format:        AT [cmds] I n [cmds]

  Description:   Displays information requested

    Command                              Function

       I0        Reports hardware identification

       I1        Reports ROM checksum

       I2        Tests and reports ROM checksum

       I3        Reports product name and software revision

       I4        Reports manufacturer information

       I5        Reports protocol options

       I8        Reports Euro-ISDN software version

                        RESTORE PROFILE ON POWER-UP

  Type:               Configuration

  Format:             AT [cmds] &Y n [cmds]

  Description:        Restores a selected profile into the active profile
                      on power-up (hard reset).

                                  RTS/CTS

  Type:          Configuration

  Format:        AT [cmds] &R n [cmds]

  Description:   Command function currently unidentified

                                SOFT RESET

  Type:                Immediate

  Format:              AT [cmds] Z n [cmds]

  Description:         Restores modem profiles previously saved in
                       non-volatile RAM using the &W command.

                           STORE ACTIVE PROFILE

  Type:            Configuration

  Format:          AT [cmds] &W n [cmds]

  Description:     Writes the values for the active profile into the
                   non-volatile RAM

EXTENDED AT COMMANDS

                          CONFIGURATION PROFILES

  Type:          Immediate

  Format:        AT [cmds] /S [cmds]

  Description:   Displays active and stored configuration profiles

SPECIAL COMMANDS

                            PROTOCOL SELECTION

  Type:          Configuration

  Format:        AT [cmds] #CH= n [cmds]

  Description:   Selects active protocol

    Command                                Mode

     #CH=7       PPP, 1 x B

     #CH=8       V.14, 1 x B

     #CH=9       V.110, 1 x B

                V.120, 1 x B

     #CH=13      Multi Link V.120, 2 x B

     #CH=16      GCI-speech, 2 x B

     #CH=18      GCI-data, 2 x B

     #CH=27      Multi Link PPP, 2 x B

                          REMOTE NUMBER SELECTION

  Type:          Configuration

  Format:        AT [cmds] #REMNBRC= n [cmds]

  Description:   Selects remote control number

                         REMOTE PASSWORD SELECTION

  Type:          Configuration

  Format:        AT [cmds] #PASSRC= n [cmds]

  Description:   Selects remote control password

                                 RING MODE

  Type:          Configuration

  Format:        AT [cmds] #RM= n [cmds]

  Description:   Selects ring mode

    Command                                Mode

      #RM0       Selects ring mode by subnumber or MSN

      #RM1       Pass on call to active profile

                                SOFT RESET

  Type:                Immediate

  Format:              AT [cmds] #Z n [cmds]

  Description:         Restores modem profiles previously saved in
                       non-volatile RAM using the &W command.

                              STORED PROFILES

  Type:          Immediate

  Format:        AT [cmds] #V [cmds]

  Description:   Displays list of stored parameters in short form

S(STATUS) -REGISTERS

                              ACTIVE PROFILE

  Type:          Register

  Format         AT [cmds] S110= n [cmds]

  Range:         0-255

  Unit:          Bit-mapped

  Description:   Selects active profile

                                 AUTOBAUD

  Type:          Register

  Format         AT [cmds] S124= n [cmds]

  Description:   Enables/disables autobaud function

    Command                              Function

     S124=0      Autobaud disabled

     S124=1      Autobaud enabled

                         BIT-MAPPED REGISTER S112

  Format:           AT [cmds] S112= n [cmds]

  Range:            Unidentified

  Unit:             Bit-mapped

  Description:      Controls ring message
                    format

       Bit                    Value                      Function

        0                                   0    Standard AT RING message
                                                 format (RING)
                                            1
                                                 Extended AT RING message
                                                 format (RING J

        1                                   0    Extended result codes
                                                 disabled
                                            1
                                                 Extended result codes
                                                 enabled

        2                                   0    Not used

        3                                   0    Standard AT format

                                            1    Extended AT format

      6 - 4                                 0    Not used

        7                                   0    Additional service
                                                 messages disabled
                                            1
                                                 Additional service
                                                 messages enabled

                                DTR COMMAND

  Type:          Register

  Format         AT [cmds] S123= n [cmds]

  Description:   Enables &D command

    Command                              Function

     S123=0      &D enabled for DTR functions

     S123=1      DTR ingnored. &D command disabled

                           EXTENDED RESULT CODES

  Type:             Register

  Format            AT [cmds] S95= n [cmds]

  Range:            0-255

  Unit:             Bit-mapped

  Description:      Works in combination with
                    the W n command to enable
                    extended result codes.
                    Features enabled by S95
                    take precedence over the
                    options selected by W n .

       Bit                    Value                      Function

        0                                   0    CONNECT result code
                                                 reports DTE speed.
                                            1
                                                 CONNECT result code
                                                 reports line speed
                                                 instead DTE speed.

        1                                   0    Verbose CONNECT result
                                                 codes display DTE or
                                            1    line speed only.

                                                 Adds "/ARQ" to all
                                                 verbose CONNECT result
                                                 codes except "NONE."

        2                                   0    CARRIER result codes
                                                 disabled.
                                            1
                                                 CARRIER result codes
                                                 enabled.

        3                                   0    PROTOCOL result codes
                                                 disabled.
                                            1
                                                 PROTOCOL result codes
                                                 enabled.

                          FACTORY DEFAULT PROFILE

  Type:             Configuration

  Format:           AT [cmds] S121= n [cmds]

  Range:            0-255

  Description:      Sets values in active profile to values found in the
                    default profile

     Command                              Function

      S121=0        Retrieve factory settings and restart

     S121=255       Disabled

                               FLOW CONTROL

  Type:          Register

  Format         AT [cmds] S39? [cmds]

  Description:   Displays the current flow control

     Value                               Meaning

       0         Flow control disabled

       3         RTS/CTS flow control enabled

       4         XON/XOFF flow control enabled

                             PROTOCOL SERVICE

  Type:          Register

  Format         AT [cmds] S111= n [cmds]

  Description:   Selects options for protocol service

    Command                              Function

       1         Voice service

       2         Data modem service

       3         Raw data service

       4         Group 3 fax service

       5         V.14

       7         PAD service

       8         V.120 service

       10        Synchronous relay service

                            RING MESSAGE TIMER

  Type:           Register

  Format          AT [cmds] S117= n [cmds]

  Range:          0-255

  Unit:           1 second

  Description:    Maximum duration allowed between two consecutive RING
                  messages

            Note: S117=0 allows for a single RING message only

                SERIAL ASYNCHRONOUS RATE & CLOCK SELECTION

  Type:          Register

  Format         AT [cmds] S114= n [cmds]

  Description:   Selects sserial asynchronous speed & clock selection

    Command                              Function

     S114=0      External clock source

     S114=1      1200bps

     S114=2      2400bps

     S114=3      300bps

     S114=4      4800bps

     S114=7      7200bps

     S114=9      9600bps

    S114=12      1200bps

    S114=14      14.400bps

    S114=19      19.2Kbps

    S114=24      2400bps

    S114=28      28.8Kbps

    S114=38      38.4Kbps

    S114=48      4800bps

    S114=20      57.6Kbps

    S114=72      7200bps

    S114=75      75bps

    S114=96      9600bps

    S114=115     115.2Kbps

    S114=255     Internal clock source

                                SOFT RESET

  Type:                Immediate

  Format:              AT [cmds] S122= n [cmds]

  Description:         Restores modem profiles previously saved in
                       non-volatile RAM using the &W command.

       Command                              Function

        S122=0         Restore setting

       S122=255        Disabled

