
IMAGRAPH CORPORATION

IMASCAN CHROMA/PCI, IMASCAN MONO/MONO-D/PCI, IMASCAN RGB/RGB-D/PCI

Card Type                  Video
Chip Set                   Tseng Labs ET4000/W32
Maximum Onboard Memory     2MB DRAM
Data Bus                   32-bit PCI
Video Types Supported      XVGA
Highest Resolution         1280 x 1024
Supported

[Image]

                                CONNECTIONS

          Function             Label           Function             Label

  VGA Out                       J1     Capture video in              J4

  VGA feature connector         J2     Daughter board connector      J5

  Daughter board connector      J3

  Note: The exact # of pins on J5 is unidentified.

                        USER CONFIGURABLE SETTINGS

                 Setting                     Label         Position

     IRQ 2/9 enabled                         JP1      Pins 1 & 2 closed

      Any IRQ disabled                        JP1      Pins 2 & 3 closed

     Factory configured - do not alter       JP2        Unidentified

  Note: JP2 sets the "Compliance Select" & does not appear on all board
  revisions.

[Image]

                                CONNECTIONS

          Function             Label           Function             Label

  Daughter board connector      J1     Daughter board connector      J6

  Note: The exact # of pins on J6 is unidentified.

[Image]

                                CONNECTIONS

          Function             Label           Function             Label

  Daughter board connector      P1     Daughter board connector      P5

  Digital port                  P2

  Note: The exact # of pins on P2 & P5 is unidentified.

MONO/MONO-D DAUGHTER BOARD JUMPER CONFIGURATION

                        USER CONFIGURABLE SETTINGS

                 Setting                     Label          Position

     Factory configured - do not alter       J1          Unidentified

     Factory configured - do not alter       J2          Unidentified

     Factory configured - do not alter       J3          Unidentified

     Factory configured - do not alter       J4          Unidentified

     Factory configured - do not alter       J5          Unidentified

     Factory configured - do not alter       J6          Unidentified

     Video1 75ohm termination enabled        J7       Pins 1 & 2 closed

      Video1 termination disabled             J7       Pins 2 & 3 closed

     Video2 75ohm termination enabled        J8       Pins 1 & 2 closed

      Video2 termination disabled             J8       Pins 2 & 3 closed

     Video3 75ohm termination enabled        J9       Pins 1 & 2 closed

      Video3 termination disabled             J9       Pins 2 & 3 closed

     Video4 75ohm termination enabled        J10      Pins 1 & 2 closed

      Video4 termination disabled             J10      Pins 2 & 3 closed

     Factory configured - do not alter       J11         Unidentified

     Factory configured - do not alter       J12         Unidentified

            Note: J1 - J3 sets the "Bus Select", J4 sets the "Field
            Invert", J5 & J6 sets the "Board Select", & J11 & J12 sets
            the "Termination".

RGB/RGB-D DAUGHTER BOARD JUMPER CONFIGURATION

                        USER CONFIGURABLE SETTINGS

                 Setting                     Label          Position

     Factory configured - do not alter       J1          Unidentified

     Factory configured - do not alter       J2          Unidentified

     Factory configured - do not alter       J3          Unidentified

     Factory configured - do not alter       J4          Unidentified

     Factory configured - do not alter       J5          Unidentified

     Factory configured - do not alter       J6          Unidentified

     Red1 75ohm termination enabled          J7       Pins 1 & 2 closed

      Red1 termination disabled               J7       Pins 2 & 3 closed

     Green1 75ohm termination enabled        J8       Pins 1 & 2 closed

      Green1 termination disabled             J8       Pins 2 & 3 closed

                    USER CONFIGURABLE SETTINGS (CONT)

                   Setting                      Label        Position

     Blue1 75ohm termination enabled             J9         Pins 1 & 2
                                                              closed

      Blue1 termination disabled                  J9         Pins 2 & 3
                                                              closed

     Red2 75ohm termination enabled             J10         Pins 1 & 2
                                                              closed

      Red2 termination disabled                  J10         Pins 2 & 3
                                                              closed

     Green2 75ohm termination enabled           J11         Pins 1 & 2
                                                              closed

      Green2 termination disabled                J11         Pins 2 & 3
                                                              closed

     Blue2 75ohm termination enabled            J12         Pins 1 & 2
                                                              closed

      Blue2 termination disabled                 J12         Pins 2 & 3
                                                              closed

            Note: J1 - J3 sets the "Bus Select", J4 sets the "Field
            Invert", & J5 & J6 sets the "Board Select".

